How to Do a Door Lock Change
Door lock replacement is a simple and affordable method to boost your home's security. However, the procedure isn't for all. It requires a certain amount of patience and skill.
The cylinder is located within the knob body. The cylinder is responsible to recognize the key when it is put into the lock.
Remove the old lock
The first step to replace a door lock is to get rid of the old one. It's a fairly simple procedure, but there are some things to be aware of. Make sure that the new lock is compatible with your door. This will ensure that it is secure and doesn't create a gap around the deadbolt or latch.
After removing the latch plate, you will be required to search for two bolts or screws in the casing's interior that hold the casing to the two halves of the lock. Remove these screws using a screwdriver before removing the lock off the door. If you have a mortise locking, there might be a set screw at the base of the handle that holds it to the spindle. Use a screwdriver to remove this screw, then pull out the doorknobs.
It is also recommended to take the deadbolt and latch plug from the hole in the door jamb. Install your new lock. If you're replacing a mortise, you should measure the distance between your lock case and your door edge to ensure that your new lock fits.
Many reasons could cause you to replace your door lock, including suspecting that someone else has the key or if you're welcoming an incoming roommate. In any event, you can save money by taking the lock off yourself rather than paying an expert to remove it. It's much simpler than most people imagine and can be done in just a few moments.
Begin by removing the handle and trim from your door. Then, pry the trim away with a flat screwdriver. You will be able twist off most of it, and in some instances the handles could come off entirely. The next step is to search for a pinhole on the inside of the handle, and insert a straightened clip into it. This will trigger the release mechanism, allowing you to remove the handle. Then, look for another small tab that is located inside of the lock and press it with a flat screwdriver. Once the spindle has been removed, you can remove the housing and cylinder.
Making a decision on a new locking system
When it comes to selecting a new lock, you have many options. Take a look at the various types of locks and pick one that matches the design of your door. Consider the backset (the distance between the door's edge and the center of the lock hole) and the cross bore (small hole that runs along the edge of the door frame). Also, make sure to choose a lock that will fit the door thickness and swing.
The majority of door locks are graded by BHMA and the American National Standards Institute to give you an idea of how well they stand up to use and how difficult to disable or pick. A grade 3 lock may be perfect for a quiet apartment in the countryside, whereas a lock of grade 1 may be better suited to a busy street near the storefront.
Most smart door locks require a digital key code to open. If you're worried about hacking or other security concerns you should consult an expert locksmith or your local police department for assistance.
Replacing the cylinder
It is easy to replace a damaged or broken door lock cylinder with a simple DIY project. It is essential to choose the right cylinder and follow the instructions. First, you must remove the handle or knob if it is present. Then, using a screwdriver, take off the trim around the lock cylinder. After the trim is removed, it is possible to remove the screws that hold the cylinder in place using a flathead. The cylinder is then gently removed out of the door.
Make sure you measure the length of the new cylinder prior to installing it. Take a measurement of the distance from the center to the right and left sides of the cylinder with the aid of a tape measure. Then, you can purchase another cylinder that has the same measurements. This will prevent cylinders from snapping when the door is hit or the key is stuck inside.
Place the replacement cylinder inside the door, and then turn the key. This will ensure that the cylinder is aligned with the carrier, which is usually located on the outside of the lock. Then, you can loosen the set screw, which should be just a couple of turns in the head. You will also need to loosen the screw in the door's edge that holds the case in place, in the event that there is one.
After you have removed the lock cylinder, you can replace it with a new lock by sliding the new cylinder into the case and tightening the set screw. You must also install the bracket that connects the cylinder to the lock indicator stem, which you can do by pulling up three small tabs on the back of the cylinder using needle-nose pliers. Then, you can attach the smaller bracket to the back of the cylinder. Then, you need to reinstall the strike plate and latch plate as well as the retaining ring connected to the top of the lock the cylinder.
Installing the new lock
If you're replacing a previous lock, you must begin by measuring the width of your door. Most residential locksets are designed to fit a door thickness of 1 3/8 to 1 3/4 inches. If your door is thicker than 1 3/8 to 1 3/4 inches, you'll need an extra thick door kit. This will require longer screws and either an extended spindle extension or tail piece for door knobs.
Most locks come with comprehensive instruction booklet that will guide you through the installation of the new hardware. Be sure to read the instructions thoroughly before beginning the process to make sure that you've followed all the steps. The manual will also provide you with an idea of the degree of skill required to perform the task. You may want to ask a person who has had experience in changing locks for assistance if you are changing locks for the first time.
It's a great idea to seal the openings of the old hardware prior to installing the new lock. replace window locks upvc will prevent the screws from slipping through the holes, and protect any tiles you have installed. It will also protect your tiles from damage caused by rust, dirt and grime. SECURAM Touch includes an ad-hoc strip of masking tape or gaffer tape. However, you can use any tape you have.
After you have removed the screws that hold the lock's interior to the outside, take the lock off immediately. It is important to do this quickly to avoid the lock from closing accidentally and damaging the mechanism.
If your new lock is equipped with a latch bolt, fit the new latch bolt into its upper cross bore. Be sure to put it in the correct position that is usually marked by an illustration on the faceplate. Then, you can screw the latch plate onto the bolt.
Finally, screw in the deadbolt and strike plate into the door jamb. Check the deadbolt several times, throwing it around to see if it extends into the strike plate. Follow the directions included in your electronic smart lock to program it. This involves downloading an application and registering your e-mail address, verifying your identity, and connecting to the wireless network in order to connect your device.